Process Inspection And Change Oil Car Engine

“The Key” to help cars always in real conditions of use and maintenance care is right vehicles, ranging from the simple to the regular car wash job requires professionalism needed thanks to auto experts such as inspection and maintenance of vehicles annually.


Looking colors catch the spark plug engine disease Toto hand cars automotive maintenance periodically Parts Autos should be replaced regularly

Special note one important step in the proactive inspection of vehicles is observed monthly car oil. The following article can help you understand the process of inspection and oil change vehicles.

Process Inspection And Change Oil Car Engine

Tools needed:

A pair of gloves or water washes your hands: Oil stains left on your hands will not be easy if a completely clean during your test is not active oil gloves. Or at least should be available in a hand sanitizer with powerful deterrence to wash their hands immediately afterward.

A pair of work boots: Have a slip, oil resistant sole will keep you safe.

A cleaning cloth: used to wipe the distich viscosity.

Engine oil: If the oil in the car is low, be ready oil bottle on the side and make sure cars are rather a correct type of oil. Use a funnel to pour the oil, spill out to avoid wastefully.

Here are the steps to replace the engine oil whatever the driver would always need to understand:

  1. Parking at the proper place

Ensure cars parked in places flat, because if parking at the roundabout where the terrain, the examination of the oil is no longer correct. After moving the car to where flatter, please persevere wait another 10 minutes before observing viscosity of the oil on the distich to make sure all the fuel had to lie still in the container.

  1. Open the bonnet

The first step is to find the lever to pull out the leg room. Depending on the type of vehicle that the bar is located in different locations, check the manual if trouble comes to find the gear.

Do not forget to remove the safety-pin once finished pulling the lever inside the car by the gear still a plastic or metal hood edges should be opened by pulling up on or to the side to allow the bonnet opens completely.

  1. Find out where the distich viscous

the-distichMost cars equipped with distich vicious striking colors for easy identification user. Lipstick viscosity with handles or T-shaped curvaceous looks like a long, slender tube that runs along the bottom of the motor fuel, or viscosity can probe in a plastic nacelle. In the case still can not find the exact location of the probe thickness, refer to the accompanying instruction book.

  1. Remove the distich viscosity out of place and clean

Pull the distich out of the slimy protective covering; then you should see a layer of oil covered the end of the lipstick. Do not read limits by results at this time give out will be inaccurate. Instead, wipe dirty oil with a towel, then to probe into the coating viscosity, initially put into place until first cue feels bottomed tanks.

  1. Take the distich out again and viscosity test oil

Pull the distich out of place and thickness determines the result of the oil in your car. Usually, there are two lines of the engraving side of the distich. Oil is located between two lines is the best moment, as close to optimal as outlined above. Clean the distich after completing the test.

Appropriate time engine oil fill-ups?

Users need to fill the engine oil when the oil is at its lowest level on the distich viscosity. Low oil level here represents the least amount of engine oil of cars need to use safely. If the engine oil is below this safe or even ultimately did not find signs of oil on the distich viscosity, it is time for cars should be fuel refill the oil in the engine compartment.

In the case of the oil remains in the safe but too close to the first bar, the experience of care and automotive maintenance experts recommend that users should fill motor oil before oil was down lowest level that has not been discovered in time to replace.

Process engine oil change:

  1. Locate the oil cap pouring mouth in the engine compartment


Find the mouth pouring oil cap is relatively easy because the place is usually marked by the word “OIL” or oil can symbol. Need to make sure the right engine oil pouring cap oil flowing mouth instead mistakenly poured into another container such cooling systems or break fluid can cause disastrous consequences. If you are unsure about anything, refer to the manual accompanying never be redundant and unnecessary.

  1. Pour the required amount of oil into the engine compartment

If you use a funnel, put it up on the cover of oil pouring mouth, then started slowly pour the necessary amount of oil into the fuel tank. Be careful not to spill across his mouth full tank lid by excess oil will be compared with that engine needs and may cause unintended consequences in time to start the motor next.

On most vicious probe, the distance between two lines usually 1-liter norm. Therefore, if oil cars at the lowest level, you will need to refill almost 1-liter engine operating at best levels. If the oil is still half the ideal level, you only need to pour 0.5 liters of oil.

Some points to note:

The inspection of oil will help you to draw conclusions about the “health” of the engine is in ideal condition or not. If you often have to replace the motor oil, such few times in January, it is a sign used motor oil or even too many vehicles meet oil leakage. Take your car to the garage to check if the vehicle has any problems or not.

Clinging on viscous oil distich can carry any color from bright yellow to black ink. If you notice unusual colors such as cream sauces like mayonnaise bold, can motor cars are in big trouble. In such cases, should stop using the vehicles immediately and schedule a test at the garage as soon as possible.

Leave A Reply

Your email address will not be published.