When the weather is in your favor, you will not have to worry about your windshield wipers but when the rainy season starts, it the wiper’s duty to manage to sweep the water away to ensure good visibility.
Mainly, in this season, there are many issues occurring and one common issue is windshield wipers not working and it is quite annoying especially when you are on the drive and you are not able to see the clear vision on the road due to rain water.
But the good news is that there are some simple fixing tips which can be “Do It Yourself”.
Following are the simple Tricks how to fix windshield wipers that stopped working.
Method 1: Cleaning Thoroughly
One possible reason of windshield wipers not working is built-up grime on the windshield which can be cleaned with the easily available material from home, you may also use glass cleaning supplies that will be available at the gas station on the go.
- Step 1 - Apply Glass Cleaner
Take some amount of glass cleaner and apply it to the windshield by freely spraying it on the windshield.
- Step 2 - Wipe Cleaner
Wipe the cleaner with the clean cloth or the rubber side of a squeegee.
- Step 3 - Apply Cleaner on Wiper Blade
After wiping cleaner, apply the glass cleaner to the wiper blades and clean blades from top to bottom softly. Ensure to remove any debris or dirt from the rubber blade.
- Step 4 - Check the condition of the blade
If you find any damages, cracks, tears or stiff which is not in the condition to work properly, you should replace it with the new one.
Related: How To Clean Windshield
Method 2: Using Wiper Fluid
Another reason for windshield wiper not working properly may be a lack of moisture on the windshield. It is stopped working if the fluid level is low. Simply refill with the fluid can solve this issue.
- Step 1 - Locate fluid reservoir
It is usually sort of a plastic container and you may find it on the bottom side of the wiper and it is usually marked it wipers icon.
- Step 2 - Remove cap and refill
Remove cap and pour windshield wiper fluid to just below the top, you may use a funnel to prevent fluid from leaking.
Method 3: Adjust The Tightness Of Wiper Assembly
Over the time, wiper assembly becomes loose or becomes too tight and this may be the cause that windshield wipers not working.
It occurs due to ice or snow, sudden changes in the temperature or may be due to the accumulation of the debris. But it can be fixed easily at home.
- Step 1 - Determine the condition of assembly whether it is too loose or too tight
In order to determine, you just need to wiggle the arm softly, if you find it wobbly then you need to tight is properly and if you find it tight, it requires to lose a bit.
- Step 2 - Snoop off plastic cover
At the base of the arm, you will find a plastic cover which you need to open using a screwdriver and reveal the nut and bolt that holds the wiper in place.
- Step 3 - Adjustment of bolts
Attach a socket with the ratchet and adjust the bolts. Do tighten or loosen the bolt.
Method 4: Replacing The Wiper Blade
Worn out wiper blades is another common cause for failed windshield wipers. Such rough blades need to replacement which is generally inexpensive and easy to swap with the old ones.
- Step 1 - Lifting up the wiper arm
Lift up the windshield wiper arm so the blade can be accessed easily.
- Step 2 - Pulling out blade
Securely hold the rubber blade from the side furthest from the wiper assembly, and pull it out.
- Step 3 - Threading in new blade
Thread the new blade assembly into the wiper structure till it locks in place.
Method 5: Replacing Etire Assembly
- Wiper arms assembly
- Flathead screwdriver
If none of the above methods worked on your windshield wipers issues, you then may need to change the entire windshield wiper assembly. It sure sounds tough task but it is far simpler which have given here proper steps:
- Step 1 - Pop out the plastic cover
The first thing you need to do to take out plastic cover which is located on the base of the assembly.
- Step 2 - Removing wiper assembly
Remove the nut that holding the wiper arm using ratchet and socket. Note that in some vehicles, there would be clip instead of nut and bolt, if it has the clip, you just need to pop off the assembly using a flathead screwdriver.
- Step 3 - Installing new wiper assembly
Take new wiper assembly and bolt it in its place or if it has clip-style, simply put the assembly in the appropriate place and press it. Tighten the retaining bolt or nut to specification.
You may also interested: Top 6 Best Mechanics Tool Set
These are the main issues with the windshield wipers, if you will find the culprit yourself, you no need to take your car to the mechanic, and there are some simple remedies that you can do it yourself.